Clamping Solutions

Rotary Ready
Expand Your CNC
Add More Functions with Rotary Kit. (i2R UCCNC Only)
Learn more
New
$999.00
i2R CNC 4th Axis Rotary Kit
i2R CNC 4th Axis Rotary Kit
Laser Ready
6w Engraving Laser
Each i2R comes Laser and Rotary Ready. Simply Plug and Play. (i2R UCCNC Only)
Learn more
New
$999.00
i2R OPT Lasers Kit - OPT PLH3D-6W-XF
i2R OPT Lasers Kit - OPT PLH3D-6W-XF
Quick view
i2R Clamps Set of 4
$38.00
Quick view
Hold Down Clamps - Pair
$19.00
Quick view
Vacuum Hold-Down Kit
$159.00
Quick view
Auto-adjust Hold-Down Clamps
$69.00
Quick view
2.2kW Vacuum pump solution
$1,499.00
Quick view
Executive CNC Vacuum Table System
from $899.00
Ways to Clamp your material to CNC

i2R Clamps Set of 4

$38.00 Save $-38.00
/

Hold Down Clamps

Set of 4

 

Hold Down Clamps - Pair

$19.00 Save $-19.00
/

The Hold Down Clamp kit provides a fast, convenient method of securing your workpiece to the table of your Axiom CNC Router. 

 

Details

The robust 5/16” T-bolt slides easily into the extruded table T-slots, and is long enough to capture nearly any material up to 3” thick. The aluminum clamping arm is 1-1/8” wide by 5-1/4” long, and is anodized to avoid marking of your materials. A large, knurled handle allows you to easily tighten to the desired pressure. Sold in pairs.

Vacuum Hold-Down Kit

$159.00 Save $-159.00
/

Struggling to secure parts on the bed of your new CNC router? You'll be amazed of the holding power of this exciting NEW accessory!

 

Details

Securing your workpiece to the bed of your CNC router often creates a challenge.  The Axiom vacuum hold-down kit is a terrific accessory which makes securing your part a snap. Use just one pod to secure a small part, or all five pods to hold something large. 

These compact Vacuum Pods are made from clear acrylic, each with it’s own vacuum seal. Each pod is connected together to cover a large area. Place the pods on your i2R/Axiom CNC table and secure with screws and T-nuts (included). Pods can be mounted either on top of your MDF spoil board or directly to the aluminum table by selecting the appropriate length screws. Cut the 1/4" hose to the desired length and connect the pods and valve to the vacuum port on the venturi. Use the remaining hose and fitting to connect your compressor to the air port on the venturi. 

You'll be amazed of the holding power of this exciting NEW accessory! 

Included:
• Vacuum Pods (5 pcs)
• On/off valve
• Venturi vacuum pump
• Mounting hardware
• End cap
• Hose (200")
• Air fitting
• Replacement gasket material 

Note: requires 1.5CFM of compressed air at 90PSI 

Auto-adjust Hold-Down Clamps

$69.00 Save $-69.00
/

(Item will be restocked Middle of APRIL)

Work holding has always been a challenge for CNC operators. Here’s a terrific pair of clamps which offer speed, ease of use, and immense holding power.

 

Details

Work holding has always been a challenge for CNC operators. Here’s a terrific pair of clamps which offer speed, ease of use, and immense holding power.

This clamp kit offers a pair of clamps which can capture materials ranging from thin veneers, to 2-3/4” thick stock. The pivoting foot has a rubber cover to avoid marring, and can extend a full 3-1/2” from the center of your T-track.

Each clamp offers durable, cast construction, and a long handle providing leverage for clamping. They rotate 360 degrees, and lock to the table via a large, knurled wheels.

The auto adjust feature allows you to pre-set the desired clamping pressure, which will remain consistent regardless of material thickness. Each clamp includes both long and short T-bolts to allow use with, or without the spoil boards installed on your table.

 

Customer Reviews

No reviews yet Write a review

2.2kW Vacuum pump solution

$1,499.00 Save $-1,499.00
/
Description

NOTE: you cannot use a vacuum table with a standard vacuum cleaner for any significant duration of time. It is a fire hazard. The pump system shown here includes a vacuum pump designed to work under pressure (which is what is needed to good vacuum clamping) for prolonged periods of use. The package also comes with all the necessary under pressure and safety connections. While the pumps are designed to work with "under pressure" you cannot close off a pump completely for flow as it will over heat. The package comes with a pre installed and tuned under pressure valve. NOTE the pressure gauge addition is an additional item and is not included


Component features:

  • Single phase vacuum pumps 2,2kW. 
  • Safe vacuum solution - with integrated thermal overload protection 
  • Under pressure values of -190mBar and -210Mbarm
  • Includes all required fittings to connect to vacuum tables (provided vac table has large gland fitting)
  • Filter provided as part of system to protect your pump from harmful particles entering
  • NOTE: you cannot just close off the flow to a pump. It will overheat. You must have an underpressure release valve. Or you have a fire hazard - this is supplied as standard
  • Pre installed underpressure device safe levels of pressure and pump performance

Executive CNC Vacuum Table System

$1,499.00 Save $-1,499.00
/

Vacuum table for EXEC 8 and Exec 16

Phenolic Table Setup with 2.2kw Pumps. 1 or 2 pump options available.